video interfaces

DVI Port: Digital Visual Interface (DVI) is a video display interface developed by the Digital Display Working Group (DDWG). An organization's department dealing with the latest technology in their projects, may also be considered a high-tech microsociety within the organization's and partners' scope. These leads connect to create an electronic circuit with a particular function (for example an amplifier, radio receiver, or oscillator). A simple schematic showing wires, a resistor, and a battery The basic components of analog circuits are wires, resistors, capacitors, inductors, diodes, and transistors. The website 'The High Tech Society' focusing on recent tech news and developments as well as game and gadget reviews could also be referred to as the high tech society. Similarly, an overdriven transistor amplifier can take on the characteristics of a controlled switch having essentially two levels of output. The term was adopted by the company as a legal name in June 2012 and is owned by Carver Networks, which is owned by entrepreneur and founder Kimberly Carver. In the vast majority of cases, binary encoding is used: one voltage (typically the more positive value) represents a binary '1' and another voltage (usually a value near the ground potential, 0 V) represents a binary '0'. Today, most electronic devices use semiconductor components to perform electron control. Electronic components have two or more electrical terminals (or leads) aside from antennas which may only have one terminal.

VGA Port:A Video Graphics Array (VGA) connector is a three-row 15-pin DE-15 connector. Analog circuit analysis employs Kirchhoff's circuit laws: all the currents at a node (a place where wires meet), and the voltage around a closed loop of wires is 0. A string of Christmas lights is a good example of a series circuit: if one goes out, they all do. As digital circuits become more complex, issues of time delay, logic races, power dissipation, non-ideal switching, on-chip and inter-chip loading, and leakage currents, become limitations to the density, speed and performance. A simple schematic showing wires, a resistor, and a battery The basic components of analog circuits are wires, resistors, capacitors, inductors, diodes, and transistors. Basic electronic components may be packaged discretely, as arrays or networks of like components, or integrated inside of packages such as semiconductor integrated circuits, hybrid integrated circuits, or thick film devices. Such considerations typically become important for circuit boards at frequencies above a GHz; integrated circuits are smaller and can be treated as lumped elements for frequencies less than 10 10GHz or so. Electronic components have two or more electrical terminals (or leads) aside from antennas which may only have one terminal. In April 1955 the IBM 608 was the first IBM product to use transistor circuits without any vacuum tubes and is believed to be the world's first all-transistorized calculator to be manufactured for the commercial market.[2][3] The 608 contained more than 3,000 germanium transistors.

HDMI Port: If your PC...

Read More

what’s Your Primary Usage

The term high definition once described a series of television systems originating from August 1936; however, these systems were only high definition when compared to earlier systems that were based on mechanical systems with as few as 30 lines of resolution. They took electronics from parlor tricks and gave us radio, television, phonographs, radar, long distance telephony and much more. Such considerations typically become important for circuit boards at frequencies above a GHz; integrated circuits are smaller and can be treated as lumped elements for frequencies less than 10 10GHz or so. The website 'The High Tech Society' focusing on recent tech news and developments as well as game and gadget reviews could also be referred to as the high tech society. Vacuum tubes (Thermionic valves) were one of the earliest electronic components. Analog circuitry is constructed from two fundamental building blocks: series and parallel circuits. Analog circuits are sometimes called linear circuits although many non-linear effects are used in analog circuits such as mixers, modulators, etc. They played a leading role in the field of microwave and high power transmission as well as television receivers until the middle of the 1980s.[1] Since that time, solid state devices have all but completely taken over.

Read More

high-definition television

The term high definition once described a series of television systems originating from August 1936; however, these systems were only high definition when compared to earlier systems that were based on mechanical systems with as few as 30 lines of resolution. This perception has led to high investment in high-tech sectors of the economy. As a consequence, extremely complex digital circuits, with billions of logic elements integrated on a single silicon chip, can be fabricated at low cost. Components are generally intended to be connected together, usually by being soldered to a printed circuit board (PCB), to create an electronic circuit with a particular function (for example an amplifier, radio receiver, or oscillator). The opposite of high tech is low technology, referring to simple, often traditional or mechanical, technology; for example, a calculator is a low-tech calculating device. Analog circuit analysis employs Kirchhoff's circuit laws: all the currents at a node (a place where wires meet), and the voltage around a closed loop of wires is 0. Commonly, electronic devices contain circuitry consisting primarily or exclusively of active semiconductors supplemented with passive elements; such a circuit is described as an electronic circuit. ...

Read More

difference between a HDTV and a monitor

Tuners aside there is still a distinct difference, between a computer display and a HDTV. When the PC just got started (or an Apple) you could use a TV as a monitor, but they quickly learned that interlaced tubes are terrible for reading text, so progressive scan displays became the norm, so along came VGA which has the same resolution as an SDTV; 640×480, but progressive. This obviously wasn’t enough and NEC released the first multiscan display that supported multiple resolutions. (I am drastically simplifying this time line) Next came flat panel displays that were fixed pixels so they used scallers to emulate the multiscan functionality (this is why LCD monitors almost never look great unless they are set to their native resolution)...

Read More